Kit de contamination de surface Elcometer 138/2

  • Revêtements de protection
  • Finition industrielle
pH-Test-Strips
Chloride-Test-Strips

La mesure de la quantité de contaminants sur une surface avant l’application d’un revêement est essentielle pour garantir d’atteindre une qualitéet une duré de vie maximales.

  • Sommaire
    • Sommaire

    • Si le revêtement est appliqué sur une surface contaminée incorrectement préparée, il peut se dégrader prématurément et nécessiter une reprise coûteuse et des coûts d’entretien élevés.

      Le kit de contamination de surface Elcometer 138/2 fournit à l’utilisateur le moyen de tester les contaminants de surface invisibles, y compris :

      • pH
      • ions chlorure
      • fer
      • sels

  • Principales caractéristiques
    • Principales caractéristiques

      Kit de contamination de surface Elcometer 138/2

      Chloride Test Strips

      Chloride Test Strips

      Chloride ions on a steel surface increase the probability that corrosion of the steel will take place even if a protective coating is applied. Chloride ions trapped under a coating in the presence of steel and moisture will form a corrosion cell. This corrosion process will result in premature failure of the protective coating and may cause blistering of coatings in immersion service.

      The chloride test strips will indicate the concentration of chloride ions in the sample solution and if the area of sample collection and the volume of water is known the concentration can be measured in parts per million or micrograms per millilitre.

      Iron Test Strips

      Iron Test Strips

      Ferrous ions are an indicator of the corrosion of steel as they are formed when the iron oxidises as a result of a corrosion cell formed between the steel and oxygen in the presence of water. The ferrous ion test strips will also indicate the concentration of ferrous ions in a sample solution in the same way as the chloride strips.

      pH Test Strips

      pH Test Strips

      These strips will determine if a solution or surface is acid or alkaline in nature. Acids form when certain gases are dissolved in water, for example, chlorine in water produces hydrochloric acid, carbon dioxide in water produces carbonic acid, sulphur dioxide in water produces sulphuric acid all of which are corrosive to steel.

      The presence of these contaminants can either be detected in a solution washed from the surface or by putting a wet ph Test Strip onto the dry surface. pH does not measure the concentration but it does indicate how acidic or alkaline the surface is. Alkaline surfaces are normally associated with either concrete surfaces that are to be coated or steel re-enforcement bars buried in concrete.

  • Informations techniques
    • Spécifications techniques
      Kit de contamination de surface Elcometer 138/2
      Numéro d'article La description Certificat
      E138----2 Kit de contamination de surface Elcometer 138/2
      Certificate of Cleanliness & Test Area available at www.elcometer.com/cert
      Plage de Mesures pH: 0 à 14, Fer: 3, 10, 25, 50, 100, 250, 500mg/l Fe²+, Chlorure: 30 - 600ppm CI
      Dimensions 300 x 220 x 75mm (11 x 8,6 x 3”)
      Poids 2,1kg (4.62lb)
      Colisage 100 bandelettes d’essais pH, 100 bandelettes d’essais fer, 40 bandelettes d’essais chlorure, 50 x Elcometer 135C Patchs pour test de Bresle, 3 seringues de 5ml (0,17fl oz), 3 aiguilles, bécher plastique de 30ml (1fl oz), mallette de transport et manuel d’instructions
      Certificat de propreté et surface d’essai disponible sur www.elcometer.com/cert
  • Normes
    • Normes
      Kit de contamination de surface Elcometer 138/2

      AS 3894.6-A, AS 3894.6-D, SSPC Guide 15

  • Téléchargements
    • Téléchargements
        • Kit de contamination de surface Elcometer 138/2 - Mode d’emploi

        • Kit de contamination de surface Elcometer 138/2 - Fiche technique

  • Numéro d'article
    • Numéro d'article
      Kit de contamination de surface Elcometer 138/2
      • Kit de contamination de surface Elcometer 138/2
        • Numéro d'article : E138----2
  • Accessoires
    • Accessoires
      Kit de contamination de surface Elcometer 138/2
      • Numéro d'article: E135----C25
      • Numéro d'article: E135----C100
      • Numéro d'article: T13820562
      • Numéro d'article: T13820564
      • Numéro d'article: T13820563
      • Numéro d'article: T13818517
      • Numéro d'article: T13818518
      • Numéro d'article: T13818519
      • Numéro d'article: T13827259

Kit de contamination de surface Elcometer 138/2

  • Revêtements de protection
  • Finition industrielle
pH-Test-Strips
Chloride-Test-Strips

La mesure de la quantité de contaminants sur une surface avant l’application d’un revêement est essentielle pour garantir d’atteindre une qualitéet une duré de vie maximales.

Sommaire

Kit de contamination de surface Elcometer 138/2

Si le revêtement est appliqué sur une surface contaminée incorrectement préparée, il peut se dégrader prématurément et nécessiter une reprise coûteuse et des coûts d’entretien élevés.

Le kit de contamination de surface Elcometer 138/2 fournit à l’utilisateur le moyen de tester les contaminants de surface invisibles, y compris :

• pH
• ions chlorure
• fer
• sels

Téléchargements
    • Kit de contamination de surface Elcometer 138/2 - Mode d’emploi

    • Kit de contamination de surface Elcometer 138/2 - Fiche technique

Principales caractéristiques

Kit de contamination de surface Elcometer 138/2

Chloride Test Strips

Chloride Test Strips

Chloride ions on a steel surface increase the probability that corrosion of the steel will take place even if a protective coating is applied. Chloride ions trapped under a coating in the presence of steel and moisture will form a corrosion cell. This corrosion process will result in premature failure of the protective coating and may cause blistering of coatings in immersion service.

The chloride test strips will indicate the concentration of chloride ions in the sample solution and if the area of sample collection and the volume of water is known the concentration can be measured in parts per million or micrograms per millilitre.

Iron Test Strips

Iron Test Strips

Ferrous ions are an indicator of the corrosion of steel as they are formed when the iron oxidises as a result of a corrosion cell formed between the steel and oxygen in the presence of water. The ferrous ion test strips will also indicate the concentration of ferrous ions in a sample solution in the same way as the chloride strips.

pH Test Strips

pH Test Strips

These strips will determine if a solution or surface is acid or alkaline in nature. Acids form when certain gases are dissolved in water, for example, chlorine in water produces hydrochloric acid, carbon dioxide in water produces carbonic acid, sulphur dioxide in water produces sulphuric acid all of which are corrosive to steel.

The presence of these contaminants can either be detected in a solution washed from the surface or by putting a wet ph Test Strip onto the dry surface. pH does not measure the concentration but it does indicate how acidic or alkaline the surface is. Alkaline surfaces are normally associated with either concrete surfaces that are to be coated or steel re-enforcement bars buried in concrete.

Spécifications techniques
Kit de contamination de surface Elcometer 138/2
Numéro d'article La description Certificat
E138----2 Kit de contamination de surface Elcometer 138/2
Certificate of Cleanliness & Test Area available at www.elcometer.com/cert
Plage de Mesures pH: 0 à 14, Fer: 3, 10, 25, 50, 100, 250, 500mg/l Fe²+, Chlorure: 30 - 600ppm CI
Dimensions 300 x 220 x 75mm (11 x 8,6 x 3”)
Poids 2,1kg (4.62lb)
Colisage 100 bandelettes d’essais pH, 100 bandelettes d’essais fer, 40 bandelettes d’essais chlorure, 50 x Elcometer 135C Patchs pour test de Bresle, 3 seringues de 5ml (0,17fl oz), 3 aiguilles, bécher plastique de 30ml (1fl oz), mallette de transport et manuel d’instructions
Certificat de propreté et surface d’essai disponible sur www.elcometer.com/cert
Normes
Kit de contamination de surface Elcometer 138/2

AS 3894.6-A, AS 3894.6-D, SSPC Guide 15

Numéro d'article
Kit de contamination de surface Elcometer 138/2
  • Kit de contamination de surface Elcometer 138/2
    • Numéro d'article : E138----2
   
Accessoires
Kit de contamination de surface Elcometer 138/2
  • Numéro d'article: E135----C25
  • Numéro d'article: E135----C100
  • Numéro d'article: T13820562
  • Numéro d'article: T13820564
  • Numéro d'article: T13820563
  • Numéro d'article: T13818517
  • Numéro d'article: T13818518
  • Numéro d'article: T13818519
  • Numéro d'article: T13827259